Használati utasítás letöltése a termék üzemeltetéséhez
SONY CMTCP100 - Mikro HiFi torony

Ha keres a használati utasítás: Mikro HiFi torony SONY CMTCP100 - igazad van. Ezen az oldalon lehet letölteni ingyen. A részleteket lásd az alábbi utasításokat.

A fájl néhány másodperc, mivel a sebesség a számítógép.
Úgy gondoljuk, hogy a segítségünkre oldalon, és mi lesz boldog, ha ellátogatnak hozzánk a jövőben.
PDF Használati útmutató letöltése Mikro HiFi torony SONY CMTCP100
Mikro HiFi torony SONY CMTCP100 Mikro HiFi torony SONY CMTCP100


Szponzorált linkek



Ez az útmutató hasznos?
A tovább gombra kattintva kérem:

Fájl mérete: 216 KB (fájl formátuma: pdf)
4-233-754-12 (1)

Micro Hi-Fi Component System
Operating Instructions Owner's Record
The model and serial numbers are located at the rear. Record the serial number in the space provided below. Refer to them whenever you call upon your Sony dealer regarding this product. Model No. Serial No.

CMT-CP100
2001 Sony Corporation


========1========

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture.
To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet. This appliance is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT MARKING is located on the rear exterior. To prevent fire, do not cover the ventilation of the apparatus with news papers, table-cloths, curtains, etc. And don't place lighted candles on the apparatus. To prevent fire or shock hazard, do not place vases on the apparatus. Don't throw a battery, dispose it as the injurious wastes.

Note to CATV system installer:

This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
INFORMATION

NOTICE FOR THE CUSTOMERS IN THE U.S.A.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
CAUTION

You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.
NOTICE FOR THE CUSTOMERS IN CANADA

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION

CAUTION

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS POLARIZED AC PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
For the customers in North America

ENERGY STAR is a U.S.
registered mark. As an ENERGY STAR partner, Sony Corporation has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

The use of optical instruments with this product will increase eye hazard.

2


========2========

Table of Contents
Parts Identification
Main unit ............................................... 4 Remote Control ..................................... 5

Sound Adjustment
Adjusting the sound ............................. 16

Other Features Getting Started
Hooking up the system .......................... 6 Inserting two size-AA (R6) batteries into the remote control ........................... 7 Setting the time ...................................... 7 Falling asleep to music -- Sleep Timer .............................. 16 Waking up to music -- Daily Timer .............................. 16

Optional Components CD
Loading the CD ..................................... 8 Playing the CD Normal Play/Shuffle Play/Repeat Play .... 8 Programming the CD tracks Program Play .............................. 9 Using the CD display ............................ 9 Hooking up the optional components.... 18

Additional Information
Precautions .......................................... 19 Troubleshooting ................................... 20 Specifications ...................................... 21
* European model only

Tuner
Presetting radio stations ....................... 10 Listening to the radio Preset Tuning ........................... 10 Using the Radio Data System (RDS)* .... 11

Tape
Loading a tape ..................................... 12 Playing a tape ...................................... 12 Recording to a tape CD Synchro Recording/ Recording Manually/Program Edit ... 13 Timer-recording radio programs ......... 14

3


========3========

Parts Identification
The items are arranged in alphabetical order. Refer to the pages indicated in parentheses () for details.

Main unit
1 2 3 4 5 6 78
Z

Y
m z

x
M X

9 q; qa qs qd qf

?/1 A

wf

qg qh qj qk ql

Z

u

x

.
m

>
M

wd

ws wa w;

BASS 3 (16) CD EJECT Z qj (8) CD SYNC qs (13, 14) CD u ws (8, 9) CD x qk (8, 9, 21) CD ./> ql (8, 9) CD m/M ql (8) DSG 5 (16, 18) FUNCTION wf (8~10, 12, 13, 18)

PHONES jack wd PLAY MODE wa (8, 9, 14) Remote sensor 2 REPEAT w; (8) TAPE EJECT Z 8 (12) TAPE REC z 6 (13) TAPE Y 7 (12~14) TAPE X qa (12~14) TAPE x 9 (12~14, 21) TAPE m/M 0 (12)

TREBLE 4 (16) TUNER BAND qd (10, 21) TUNING MODE qg (10, 11) TUNING +/ qf (10, 11) VOLUME qh (17)

BUTTON DESCRIPTIONS
@/1 (power) 1 (7, 10, 14, 17, 18)

4


========4========

Remote Control
Parts Identification

1 2 3

ws wa w; ql qk qj qh qg qf

4 5 6 7 8 9 0 qa

qd qs

CD REPEAT qk (8) CD N ws (8, 9) DIR MODE ql (12~14) DISPLAY 2 (9, 11) DSG 1 (16) ENTER qd (7, 10, 14, 17) MEMORY qh (10) PLAY MODE 9 (8, 9, 14)

SLEEP qf (16) STEREO/MONO qj (11) TAPE Y w; (12~14) TIMER SELECT qs (15, 17) TIMER SET qg (7, 14, 17) TUNER/BAND wa (10) TUNING MODE q; (10, 11) VOL +/ qa (17)

BUTTON DESCRIPTIONS
X 4 (8, 12~14) x 5 (8, 9, 12~14) ./> 6 (7~10, 14, 17) m/M 7 (8, 10~12) @/1 (power) 3 (7, 10, 14, 17) z REC 8 (13)

5


========5========

Getting Started

Hooking up the system
Follow steps 1 through 4 of the procedure below to hook up your system using the supplied cords and accessories.
AM loop antenna

FM antenna

Right speaker

2

Left speaker

1 3 4
1 Connect the speakers.

Connect the right and left speaker cords to the SPEAKER terminals as shown below.

3 R #

3 L #

Gray (3)

Jack type A
EN ANT NA

Extend the FM wire antenna horizontally

AM loop antenna

Black (#)
AM U

75 FM

Insert this portion Jack type B

2 Connect the FM and AM antennas.

ANT

ENN

A

Set the AM loop antenna up before connecting it.
AM

Extend the FM AM loop wire antenna horizontally antenna
75 FM

U

U

6


========6========

3 For models with a voltage selector, set VOLTAGE SELECTOR to the local power line voltage.
110V-120V

Setting the time
1 Turn on the system. 2 Press TIMER SET on the remote.
If you are setting the clock for the first time, go to step 5.
Getting Started

220V-240V VOLTAGE SELECTOR

3 Press ./> on the remote
repeatedly until "SET CLOCK" appears in the display.

4 Connect the power cord to a wall outlet.

If the plug does not fit the wall socket, detach the supplied plug adaptor (only for models equipped with an adaptor). To turn on the system, press @/1.

4 Press ENTER on the remote.
The hour indication flashes.

5 Press ./> on the remote
repeatedly to set the hour.

Inserting two size-AA (R6) batteries into the remote control
e E e E

6 Press ENTER on the remote.
The minute indication flashes.

7 Press ./> on the remote
repeatedly to set the minute.

8 Press ENTER on the remote.
The clock will begin operating.
To reset the system clock

Start over from step 1.

Tip

When the remote no longer operates the system, replace both batteries with new ones.
Note

If you do not use the remote for a long period of time, remove the batteries to prevent possible damage from battery leakage and corrosion.

7


========7========

CD

2 Press PLAY MODE repeatedly until the

Loading the CD
1 Press CD EJECT Z.
The disc tray slides out.

mode you want appears in the display.
Select To play

No display SHUFFLE PGM

The CD in original order. The tracks on the CD in random order. The tracks on the CD in any order that you want (see "Programming the CD tracks" on page 9).

2 Load a CD onto the disc tray.
?/1 Z x u

Load with the label side up. When you play a CD single (8 cm CD), load it onto the inner circle of the tray.

> .
m M

3 Press CD u (or CD N on the remote).
Other Operations
To Do this

Stop playback Pause

Press CD x. Press CD u (or X on the remote). Press again to resume playback. During playback or pause, press CD ./> repeatedly until you find the desired track. During playback, press and hold down CD m/M until you find the desired point. Press CD EJECT Z. Press REPEAT repeatedly during playback until "REPEAT" or "REPEAT 1" appears in the display. REPEAT: For all the tracks on the CD. REPEAT 1: For only the currently playing track. To cancel playing repeatedly, press REPEAT repeatedly until "REPEAT" and "REPEAT 1" disappear from the display.

3 Press CD EJECT Z again to close the
disc tray.
Notes

Select a track

The disc cannot be viewed through the front window when a CD single (8 cm CD) is loaded. The characters printed on the disc appear upside down when viewed through the front window.

Find a point in a track

Playing the CD
Remove the CD

Normal Play/Shuffle Play/Repeat Play
This system lets you play CDs in different play modes.

Play repeatedly (Repeat Play)

1
Track number

005
Playing time

1 Turn FUNCTION until "CD" appears in
the display.

The indicator surrounding the CD u and CD x buttons lights up.

8


========8========

Programming the CD tracks
Program Play
You can make a program of up to 24 tracks on a CD in any order that you want.

Using the CD display
Press DISPLAY on the remote repeatedly.

The display changes as follows:
During normal playback

1 Turn FUNCTION until "CD" appears in
the display.

2 Press PLAY MODE repeatedly until
"PGM" appears in the display.

Current track number and elapsed playing time of the track t Current track number and remaining playing time of the track t Remaining playing time of the entire CD t Clock display t Current track number and elapsed playing time of the track t ......
While the CD is stopped

CD

3 Press CD ./> repeatedly until the
desired track number appears in the display.
PGM

Total playing time t Clock display t Current source display t Total playing time t ......
Note

3
Selected track number

243
Total playing time

If the CD contains 25 tracks or more, the remaining playing time of the current track will appears as "---.--" for each track starting with the 25th.

4 Press PLAY MODE.
The selected track is programmed. The selection number appears in the display.

5 To program additional tracks, repeat
steps 3 and 4.

6 Press CD u (or CD N on the remote).
To Do this

Cancel Program Play

Press PLAY MODE repeatedly until "PGM" disappears from the display. Do steps 3 and 4 with Program Play stopped. Press CD x with Program Play stopped.

Add a track to the end of the program Erase the entire program
Tips

The program you made remains after Program Play finishes. To play the program again, switch the function to CD, and then press CD u (or CD N on the remote). "--.--" appears in the display when the total program time exceeds 100 minutes.

9


========9========

Tuner
To change the preset number

Presetting radio stations
The system can store a total of 30 preset stations (20 for FM and 10 for AM).

Start over from step 2.
Tip

1 Turn FUNCTION until "TUNER" appears
in the display.

The preset stations are saved in the system's memory for about a day even if you disconnect the power cord or a power failure occurs.

The indicator surrounding the TUNER BAND button lights up.

2 Press TUNER BAND to select FM or
AM.

To change the AM tuning interval (not applicable on the European, Middle Eastern and Philippine models)
The AM tuning interval is factory-preset to 9 kHz (or 10 kHz for some areas). To switch the AM tuning interval, tune in any AM station first, then turn off the system. Pressing and holding down TUNING +, turn the system back on. When you change the interval, all the AM preset stations are erased. To change back to the original interval, tune in any AM station first, then turn off the system. Pressing and holding down TUNING , turn the system back on.

3 Press TUNING MODE repeatedly until
"AUTO" appears in the display.

4 Press TUNING +/ (or m/M on the
remote).

The frequency changes as the system scans for a station. Scanning stops automatically when a station is tuned in. At that time, "TUNED" and "STEREO" (for stereo program only) appear.

Listening to the radio
Preset Tuning
Presetting radio stations in the system's memory in advance make it easy to tune in those stations later (see "Presetting radio stations" on this page).

5 Press MEMORY on the remote.
A preset number flashes.
PRESET STEREO
TUNED

1FM1005
Preset number Frequency

MHz

1 Turn FUNCTION until "TUNER" appears
in the display.

6 Press ./> on the remote
repeatedly to select the preset number that you want.

2 Press TUNER BAND to select FM or
AM.

3 Press TUNING MODE repeatedly until
"PRESET" appears in the display.

7 Press ENTER on the remote.
The station is stored to the selected preset number.

4 Press TUNING +/ (or m/M on the
remote) repeatedly to display the preset number of the desired station. To turn off the radio

8 Repeat steps 2 through 7 to preset
other stations. To tune in a weak station

Press ?/1.

In step 3, press TUNING MODE repeatedly until "AUTO" and "PRESET" disappear from the display, then press TUNING +/ (or m/M on the remote) repeatedly to tune in the station.

10


========10========

To tune in a non-preset radio station

In step 3, press TUNING MODE repeatedly until "AUTO" and "PRESET" disappear from the display, then press TUNING +/ (or m/M on the remote) repeatedly to tune in the desired station (Manual Tuning).
Tips

If there is static during an FM broadcast, press STEREO/MONO on the remote until "MONO" appears in the display. After "MONO" scrolls across the display, the frequency will appear. The broadcast will no longer be in stereo, but the reception will improve. To improve the reception, adjust the supplied antennas or connect an external antenna.

Tuner

Using the Radio Data System (RDS)
(European model only) What is the Radio Data System?

Radio Data System (RDS)* is a broadcasting service that allows radio stations to send additional information along with the regular program signal.
Note

RDS may not work properly if the station you have tuned in is not transmitting the RDS signal properly or if the signal is weak. * Not all FM stations provide RDS service, nor do they all provide the same type of services. If you are not familiar with the RDS system, check with your local radio stations for details on RDS services in your area.

Receiving RDS broadcasts
Simply select a station from the FM band.

When you tune in a station that provides RDS services, the station name appears in the display.
To check the RDS information

Each time you press DISPLAY on the remote, the display changes as follows: Station name* t Frequency t Clock display t Station name* t ......
* If the RDS broadcast is not properly received, the station name may not appear in the display.

11


========11========

Tape Other Operations

Loading a tape
1 Press TAPE EJECT Z. 2 Load a recorded/recordable tape into
the cassette holder.
With the side you want to play/ record on facing towards you

To

Do this

Stop playback Pause Fast-forward or rewind Remove the tape

Press TAPE x. Press TAPE X. Press again to resume playback. With the tape stopped, press TAPE m/M. Press TAPE EJECT Z.

Z

Y
m z

x
M X

?/1

Playing a tape
You can use Type I (normal) tape.

1 Load a recorded tape into the cassette
holder.

2 Turn FUNCTION until "TAPE" appears
in the display.

The indicator surrounding the TAPE Y and TAPE x buttons lights up.

3 Press DIR MODE on the remote
repeatedly to select " " to play one side of the tape, " " to play both sides, or " "* to play both sides repeatedly.
* The tape automatically stops after playing back five times.

4 Press TAPE Y.
Press TAPE Y again to play the reverse side. The tape starts playing back.

12


========12========

Recording to a tape
CD Synchro Recording/Recording Manually/Program Edit
You can record from a CD, radio or any of the connected components. You can use Type I (normal) tape.
Recording from a CD (CD Synchro Recording) Load a recordable tape into the cassette holder. Load a CD onto the disc tray. Turn FUNCTION until "CD" appears in the display. Press CD SYNC. Turn FUNCTION to select the source you want to record from. Load a CD or tune in the desired station. Press TAPE REC z (or z REC on the remote).

Steps

Recording manually

1 2 3 4

Tape

The tape stands by for recording. " " and "B" (or "b") appear.
" To start recording on the side facing away from you, press TAPE Y until " ." changes to "

5 6

Press DIR MODE on the remote repeatedly to select " " to record on one side of " or " " to record on both sides. the tape, or " Press TAPE X. Press TAPE X, and then start playing the desired source.

To stop recording

Press TAPE x.
Tip

For recording manually: To pause recording, press TAPE X.

continued

13


========13========

Recording to a tape (continued)

Recording CD tracks in your favorite order
Program Edit

Timer-recording radio programs
To timer-record, make sure that you have set the system clock correctly (see "Setting the time" on page 7) and preset the radio station (see "Presetting radio stations" on page 10).

1 Load a recordable tape into the
cassette holder.

2 Load a CD onto the disc tray. 3 Do steps 1 through 5 in Program Play
(see page 9).

1 Tune in the desired preset radio station
(see "Listening to the radio" on page 10).

4 Press CD SYNC.
The tape stands by for recording and the CD stands by for playback. " " and "B" (or "b") appear, and the CD SYNC indicator lights up. To start recording on the side facing away from you, press TAPE Y until " " changes to " ."

2 Load a recordable tape. 3 Press TIMER SET on the remote. 4 Press ./> on the remote
repeatedly until "SET REC" appears in the display.

"SET REC" scrolls and "c REC" appears in the display.

5 Press ENTER on the remote.
"ON TIME" appears, then the hour indication flashes.

5 Press DIR MODE on the remote
repeatedly to select " " to record on " or " " one side of the tape, or " to record on both sides.

6 Set the starting time.
Press ./> on the remote repeatedly to set the hour, then press ENTER on the remote. The minute indication begins flashing next. Press ./> on the remote repeatedly to set the minute, then press ENTER on the remote. "OFF TIME" appears, then the hour indication flashes again.

6 Press TAPE X.
To Do this

Stop recording Cancel Program Edit
Tip

Press TAPE x. Press PLAY MODE repeatedly until "PGM" disappears from the display.

You can specify which tracks are recorded on each side of the tape during CD Synchro Recording. In step 3, after programming the tracks for first side, press X on the remote. You can then program the tracks for the other side. In this case, make sure you select " " or " " in step 5.

7 Set the stopping time by repeating step
6.

The start time, the stopping time, "TUNER", and the preset station appear in turn, then the original display returns.

8 Press @/1 to turn off the system.
When the recording starts, the volume level is automatically set to the minimum.

14


========14========

To

Do this

Check the settings

Press TIMER SELECT on the remote repeatedly until "c REC" appears in the display. The preset items appear in turn. Press TIMER SELECT on the remote repeatedly until "c REC" disappears from the display.

Turn off the timer

Tip

Once you set the timer, the time settings will remain in the system's memory until you change them, even when you turn the system or the timer off. The settings that were last used will be in effect when you turn the timer on again.
Notes

Tape

The system will turn on 15 seconds before the specified starting time. If the system is turned on at the specified starting time, recording will not occur. When you have set the Sleep Timer, the timer recording will not operate until the Sleep Timer Function is turned off.

15


========15========

Sound Adjustment

Other Features

Adjusting the sound
Generating a more dynamic sound (Dynamic Sound Generator) Press DSG.

Falling asleep to music
-- Sleep Timer
The Sleep Timer Function lets you specify a sleep time, after which the system stops playing and turns off automatically. You can thus fall asleep to music.
Press SLEEP on the remote repeatedly.

To cancel the DSG, press DSG again.
Adjusting the bass Turn BASS.

You can adjust the bass in 7 steps.
Adjusting the treble Turn TREBLE.

The sleep time changes as follows: AUTO* t 90MIN t 80MIN t 70MIN t ... t 10MIN t OFF t AUTO* t ...
* The system turns off after the current CD or tape finishes playing (up to 100 minutes). The system also turns off when you manually stop the CD or tape.
To Press

You can adjust the treble in 7 steps.

Check the remaining sleep time Change the sleep time

SLEEP on the remote once. SLEEP on the remote repeatedly until the time you want appears. SLEEP on the remote repeatedly until "OFF" appears.

Cancel the Sleep Timer Function

Waking up to music
-- Daily Timer
By setting the Daily Timer, you can make the system automatically turn on and off at specified times. To use this function, make sure that you have set the system clock correctly (see "Setting the time" on page 7).

16


========16========

1 Prepare the music source you want to
listen to when the system turns on.

8 Press ./> on the remote
repeatedly until the music source you want appears.

CD: Load a CD. To start playing from a specific track, make a program (see "Programming the CD tracks" on page 9). Tape: Load a tape with the side you want to play facing towards you. Radio: Tune in the preset radio station that you want (see "Listening to the radio" on page 10).

The display changes as follows:
t TUNER y CD T t TAPE T

9 Press ENTER on the remote.
The starting time, the stopping time, and the music source appear in turn, then the original display returns.

2 Adjust the volume. 3 Press TIMER SET on the remote. 4 Press ./> on the remote
repeatedly until "SET DAILY" appears in the display.

10 Press @/1 to turn off the system.
To Do this

Check the settings

"SET DAILY" scrolls and "c DAILY" appears in the display.

5 Press ENTER on the remote.
"ON TIME" appears, then the hour indication flashes.

Press TIMER SELECT on the remote repeatedly until "c DAILY" appears in the display. The preset items appear in turn. Press TIMER SELECT on the remote repeatedly until "c DAILY" disappears from the display.

Other Features

Turn off the timer

6 Set the starting time.
Press ./> on the remote repeatedly to set the hour, then press ENTER on the remote. The minute indication begins flashing next. Press ./> on the remote repeatedly to set the minute, then press ENTER on the remote. "OFF TIME" appears, then the hour indication flashes again.

Tip

Once you set the timer, the time settings will remain in the system's memory until you change them, even when you turn the system or the timer off. The settings that were last used will be in effect when you turn the timer on again.
Notes

7 Set the stopping time by repeating step
6.

The system will turn on 15 seconds before the specified starting time. When you have set the Sleep Timer, the Daily Timer will not operate until the Sleep Timer Function is turned off.

17


========17========

Optional Components
Tip

Hooking up the optional components
You can connect a variety of components to your system in order to enhance it. Make sure that the color of the plugs matches that of the connectors.
To the audio output jacks on your MD deck/VCR

If you cannot select "VIDEO" by turning FUNCTION, press @/1 while pressing down DSG in standby mode. The function will change from "MD" to "VIDEO", and "VIDEO" will appear in the display. To change back to "MD", repeat this procedure.

To the digital input connector on your MD deck*

* If the jack is covered with a cap, remove it before use.
To Do This

Make a digital recording from CD to MD Listen to the connected MD deck Listen to the connected VCR

Connect the optical cable.

Turn FUNCTION until "MD" appears in the display. Turn FUNCTION until "VIDEO" appears in the display.

18


========18========

Additional Information
Notes on CDs

Precautions
On operating voltage
Before operating the system, check that the operating voltage of your system is identical with the voltage of your local power supply.

Before playing a CD, clean the CD surface with a cleaning cloth. Wipe the CD from the center out. Do not play a CD with tape, stickers, or adhesives on any of its surfaces as this may damage the system. Do not use solvents. Do not expose the CDs to direct sunlight or heat sources.

On safety
The unit is not disconnected from the AC power source (mains) as long as it is connected to the wall outlet, even if the unit itself has been turned off. Unplug the system from the wall outlet (mains) if it will not be used for an extended period of time. To disconnect the power cord (mains lead), pull it out by the plug. Never pull the cord itself. Should any solid object or liquid fall into the system, unplug the system and have it checked by qualified personnel before operating it any further. AC power cord must be changed only at the qualified service shop.

Cleaning the cabinet
Clean the cabinet, panel and controls with a soft cloth slightly moistened with mild detergent solution. Do not use any type of abrasive pad, scouring powder or solvent such as thinner, benzene or alcohol.

To save a tape permanently
To prevent a tape from being accidentally recorded over, break off the cassette tabs from side A or side B as illustrated.
Break off the cassette tab

Additional Information

On placement
Do not place the system in an inclined position. Do not place the system in locations where it is: -- Extremely hot or cold -- Dusty or dirty -- Very humid -- Subject to vibrations -- Subject to direct sunlight

If you later want to reuse the tape for recording, cover the broken tab with adhesive tape.

On heat buildup
Although the unit heats up during operation, this is not a malfunction. Place the system in a location with adequate ventilation to prevent heat build-up in the system. If you continuously use this system at a large volume, the cabinet temperature of the top, side and bottom rises considerably. To avoid burning yourself, do not touch the cabinet. To prevent a malfunction, do not cover the ventilation hole for the cooling fan.

Before placing a cassette in the tape deck
Take up any slack in the tape. Otherwise the tape may get entangled in the tape deck's playing mechanism and become damaged.

When using a tape longer than 90 minutes
The tape is very elastic. Do not change the tape operations such as play, stop, and fast-winding etc. too frequently. The tape may get entangled in the tape deck's playing mechanism.

On operation
If the system is brought directly from a cold place to a warm place, or is placed in a very damp room, moisture may condense on the lens inside the CD player. Should this occur, the system will not operate properly. Remove the CD and leave the system turned on for about an hour until the moisture evaporates. When moving the unit, remove any disc that may be on the disc tray. If you have any questions or problems concerning your system, please consult your nearest Sony dealer.

Cleaning the tape heads
Clean the tape heads after every 10 hours of use. Make sure to clean the tape heads before making an important recording or after playing an old tape. Use a commercially available dry-type or wet-type cleaning cassette. For details, refer to the instructions of the cleaning cassette.

Demagnetizing the tape heads
Demagnetize the tape heads and the metal parts that have contact with the tape after every 20 to 30 hours of use with a commercially available demagnetizing cassette. For details, refer to the instructions of the demagnetizing cassette.

19


========19========

Troubleshooting
Should you encounter a problem with your system, do the following: 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the troubleshooting checklist below and take the indicated corrective action. If the problem persists after doing all of the above, consult your nearest Sony dealer.

Speakers
Sound comes from only one channel, or the left and right volumes are unbalanced.

Check the speaker connections and placement.

CD Player
The CD will not play.

General
There is no sound from the speakers.

The CD is dirty. The surface of the CD is scratched. Replace the CD. The CD is loaded with the label side down. Condensation has built up in the system. Remove the CD and leave the system turned on for about an hour until the moisture evaporates.
Play does not start from the first track.

Adjust the volume. The headphones are connected. Check the speaker connections.
There is severe hum or noise.

The player is in Program or Shuffle Play. Press PLAY MODE repeatedly until "PGM" and "SHUFFLE" disappear.

A TV or VCR is placed too close to the unit. Move the unit away from the TV or VCR.
"0:00" (or "AM 12:00") flashes in the display.

Tape Deck
Recording cannot be done.

A power interruption has occurred. Set the clock (see page 7) and timer settings (see pages 14 and 16) again.
The timer does not function.

Make sure the clock is correctly set (see page 7). You cannot operate the Daily Timer and the timer recording at the same time.
"c DAILY" and "c REC" do not appear when you press TIMER SELECT on the remote.

There is no tape in the cassette holder. The record protect tab has been removed from the cassette (see page 19). The tape has come to the end.
The tape does not record or play, or there is a decrease in sound level.

Make sure each timer is correctly set (see pages 14 and 16). Make sure the clock is correctly set (see page 7).
The color on the TV screen is irregular.

The heads are dirty. Clean them (see page 19). The record/playback heads are magnetized. Demagnetize them (see page 19).
The tape does not erase completely.

Move the speakers farther away from the TV set.
The remote does not work.

The record/playback heads are magnetized. Demagnetize them (see page 19).
There is excessive wow or flutter, or the sound drops out.

There is an obstacle between the remote and the unit. You are not pointing the remote in the direction of the system's sensor. The batteries in the remote have run down. Replace the batteries. Make sure that the batteries are inserted correctly.

The capstans or pinch rollers are dirty. Clean them (see page 19).
Noise increases or the high frequencies are missing.

The record/playback heads are magnetized. Demagnetize them (see page 19).

20


========20========

Tuner
There is a severe hum or noise ("TUNED" or "STEREO" flashes).

Specifications
Amplifier section For the U.S. model AUDIO POWER SPECIFICATIONS

Adjust the antenna. The signal strength is too weak. Connect an external antenna. Make sure that the antenna is connected properly. Do not bend or roll up the antenna. The two wires comprising the FM antenna have been pulled further apart since the system was first purchased. Repair or replace with a new one. The AM antenna wire is detached from the stand. Keep the antennas as far away from the speaker cords as possible.
A stereo FM program cannot be received in stereo.

POWER OUTPUT AND TOTAL HARMONIC DISTORTION: With 6-ohm loads, both channels driven, from 70 - 20,000 Hz; rated 18 watts per channel minimum RMS power, with no more than 0.9% total harmonic distortion from 250 milliwatts to rated output.
North American model: Continuous RMS power output (reference): 35 + 35 W (6 ohms at 1 kHz, 10% THD) Total harmonic distortion less than 0.07% (6 ohms at 1 kHz, 18 W) European model: DIN power output (rated): 30 + 30 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 35 + 35 W (6 ohms at 1 kHz, 10% THD) Music power output (reference): 85 + 85 W Other models: The following measured at 230 V AC, 60 Hz DIN power output (rated): 27 + 27 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 32 + 32 W (6 ohms at 1 kHz, 10% THD) The following measured at 220 V AC, 60 Hz DIN power output (rated): 23 + 23 W (6 ohms at 1 kHz, DIN) Continuous RMS power output (reference): 26 + 26 W (6 ohms at 1 kHz, 10% THD) Inputs AUDIO IN MD (VIDEO) (phono jacks): Sensitivity 500/250 mV, impedance 47 kilohms Outputs OPTICAL DIGITAL OUT (CD): Optical PHONES: Accepts headphones with an impedance of 8 ohms or more SPEAKER: 6 ohms

Additional Information

Press STEREO/MONO on the remote until "STEREO" appears in the display.

Resetting the system With the system turned on, press TAPE x, CD x and TUNER BAND at the same time.

The system is reset to the factory settings. All previous settings are cleared and must be set again.

Messages
One of the following messages may appear or flash in the display during operations.
NO DISC

There is no CD on the disc tray.
PGM FULL

You try to program 25 tracks or more.

continued

21


========21========

Specifications (continued)
CD player section
System Laser Compact disc and digital audio system Semiconductor laser ( = 780 nm) Emission duration: continuous 780 - 790 nm 2 Hz - 20 kHz (0.5 dB)

Speakers
Speaker system Speaker units Two-way, bass reflex system 12 cm dia., cone type woofer 2.5 cm dia., semi-dometype tweeter 6 ohms Approx. 150 252 255 mm Approx. 2.6 kg net per speaker

Rated impedance Dimensions (w/h/d) Mass

Wavelength Frequency response

Tape player section
Recording system Frequency response Wow and flutter 4-track 2-channel stereo 50 - 13,000 Hz (3 dB), using a Sony TYPE I cassette 0.15% W. Peak (IEC) 0.1% W. RMS (NAB) 0.2% W. Peak (DIN)

General
Power requirements North American model: European model: Australian model: Mexican model: Other models: 120 V AC, 60 Hz 230 V AC, 50/60 Hz 220 - 240 V AC, 50/60 Hz 120 V AC, 60 Hz 110 - 120 V or 220 240 V AC , 50/60 Hz Adjustable with voltage selector See the nameplate 0.5 W (in the standby mode) See the nameplate Approx. 190 252 345 mm incl. projecting parts and controls Approx. 5.6 kg Remote commander (1) AM loop antenna (1) FM wire antenna (1) Batteries (2)

Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section

Power consumption European model: Other models: Dimensions (w/h/d)

Tuning range North American model: Other models: Antenna Antenna terminals Intermediate frequency
AM tuner section

87.5 - 108.0 MHz (100-kHz step) 87.5 - 108.0 MHz (50-kHz step) FM wire antenna 75 ohm unbalanced 10.7 MHz

Mass Supplied accessories

Tuning range Pan-American model:

530 - 1,710 kHz (with the tuning interval set at 10 kHz) 531 - 1,710 kHz (with the tuning interval set at 9 kHz) European model: 531 - 1,602 kHz (with the tuning interval set at 9 kHz) Middle Eastern and Philippine models: 531 - 1,602 kHz (with the tuning interval set at 9 kHz) Other models: 530 - 1,710 kHz (with the tuning interval set at 10 kHz) 531 - 1,602 kHz (with the tuning interval set at 9 kHz) Antenna AM loop antenna, external antenna terminal Intermediate frequency 450 kHz

Design and specifications are subject to change without notice.

22


========22========

Additional Information

23


========23========

Sony Corporation

Printed in Korea


========24========


========25========



További információért, kérjük töltse le a utasításokat.

Szponzorált linkek
Előnézet használati utasítás
Típus Mikro HiFi torony
Név SONY CMTCP100
Model CMTCP 100
Fájl mérete 216 KB
Number of pages 24 pages
fájl formátuma pdf
Nyelv Mikro HiFi torony SONY CMTCP100 English English,